"Swallow" mahogany runabout
Здравейте,
Реших да направя една лодка или по-точно ето тази:
http://www.rcgroups.com/forums/showt...hlight=swallow
Като за начало купих чертежа от момъка от RCGROUPS за 20 лири.Получих много подробен чертеж,файловете за лазерно рязане,много снимки и информация за изработването.
Шпанготите са от 3 мм шперплат.
http://imageshack.us/a/img196/8431/wp000135.jpg
Корпусът се изработва от 1,5 мм балса и 1,5 мм махагон.
Дължинта е 1200 мм.Пристигна и дейвудът:
http://imageshack.us/a/img202/9110/wp000023k.jpg
Дължина 50 см.Поръчан ето от тук:
http://www.model-dockyard.com/acatal...ropshafts.html
Малко снимки от процеса на изработване на корпуса:
http://imageshack.us/a/img203/7223/83355476.jpg
http://imageshack.us/a/img189/7558/dsc02404mh.jpg
http://imageshack.us/a/img10/7581/wp000151r.jpg
http://imageshack.us/a/img84/3332/wp000029c.jpg
http://imageshack.us/a/img687/38/wp000021x.jpg
http://imageshack.us/a/img829/2255/wp000022n.jpg
В момента корпусът е готов до цялостно завършена облицовка с балсата:
http://imageshack.us/a/img545/9251/wp000052v.jpg
Готови са и вратите на моторният отсек и капака за достъп до механизамът на руля:
http://imageshack.us/a/img9/5039/wp000057o.jpg
Следва доста шкурене и китване до предаване на завършен вид на формите на корпусът.
"Swallow" mahogany runabout
По принцип се придържам към чертежа.Но правя лодката за удоволствие.Не е проблем да се променят неща по нея.Какво е оптималното рзастояние между винта и руля?В момента при мен по чертеж е 37 мм
между оста на руля и винта.Дейдвуда само е сложен на мястото си но не е закрепен.Руля също няма определено все още точно място,така,че разстояниеето може да се корегира.Ще се съм благодарен за мнения и препоръки.
"Swallow" mahogany runabout
Здравейе,
Събирам мнения.Не,че му е дошло времето,но да се подготвя психически за цената :D :D
Тези дни очаквам махагонът та се сетих за лодката(не съм пипал по нея от бая време).
Англичнинът кара неговата с граупнерски мотор SPEED 600/160 А контролер и трилопатен 40 мм винт.
Каза,че върви добре но ми препоръча да търся безчетков мотор аналог на 3,5 сс мотор.При пробите лодката е показала по-голяма скорост и добро държане на водата с пластмасов трилопатен винт за
скоростни лодки и диаметър 35 мм.Всякакви препоръки и съвети ще са ми от полза.
"Swallow" mahogany runabout
Още малко напредък по обличането на палубата.Съмнявам се да повторя още един път подобно редене на 1,5 х 1,5 мм летви :laughing::laughing: Трябва да нямаш нервна система.
http://imageshack.us/a/img138/3988/wp000136j.jpg
http://imageshack.us/a/img12/5884/wp000137b.jpg
Капаците на отворите са облечени.Остава да изрежа излишъка от летвите
http://imageshack.us/a/img827/6776/wp000139c.jpg
"Swallow" mahogany runabout
"Swallow" mahogany runabout
Бях се нагласил да поработя по яхтата когато днес най-после от
Англия пристигнаха "златните" летви махагон.Голямо чакане падна.
Сигурно пеш са ги носили до България ::laughing:
http://imageshack.us/a/img19/1002/wp000174c.jpg
http://imageshack.us/a/img841/1548/wp000177v.jpg
Много не ми се занимаваше тази вечер,но реших да сложа по един ред :wink:
http://imageshack.us/a/img708/1655/wp000178v.jpg
Ще направя по-качествени снимки когато има видим резултат от обличането с махагона.
"Swallow" mahogany runabout
"Swallow" mahogany runabout
"Swallow" mahogany runabout
"Swallow" mahogany runabout
Да,наистина стана красива лодка,но на края видях доста зор.В преходите от страничната част към палубата имаше голямо напасване на махагона.С балсата нямаше проблем защото тя поддава на усукване и изривяване по широчина на летвата и без проблем я извивах по малките радиуси,но махагонът е много твърд и се наложи да разкроявам летвите на малки парчета за да мога да оформя закръгленията.Резултатът си заслужаваше труда.Вече корпусът е готов.Следва шкурене и тогава ще има снимки.Сега ще се занимавам да довърша кокпита за да е готово всичко за лакирането.
"Swallow" mahogany runabout
Малко работа по кокпита:
http://imageshack.us/a/img826/3374/wp000206.jpg
http://imageshack.us/a/img12/6255/wp000208h.jpg
Пък с какво ще я задвижвам :Annoyed:
Все още нямам решение по този въпрос.Ако някой има предложения да казва.
За сега мога да дам само следните данни:
Дължина 1200 мм
Максимална широчина 245 мм
Височина 110 мм
Когато корпусът е готов ще знам и колко тежи до тук без мотор и електроника.Трябва да премеря колко е
водоизместването и ще монтирам два кръга за водно охлаждане (за мотора и контролера)
"Swallow" mahogany runabout
Край на темата.Явно на никой не му е интересно.Ако беше за опюване на някой,до сега темата щеше да е поне 20 страници.Всяка минута писане по БГ форумите за моделизъм е загубено време което може да се използва за работа по моделите.
"Swallow" mahogany runabout
Лодката започва да придобива завършен вид.
http://img705.imageshack.us/img705/8664/dsc02510u.jpg
http://img842.imageshack.us/img842/2040/dsc02507vj.jpg
Имам още детайли за довършване след което следва шкурене на корпусът,тук там китосване и лакирането.
"Swallow" mahogany runabout